Ultrasonic Gasoline Vaporizer by Sul-tech

by Buddy Vapesit

an ultra sonic vaporizer for gasoline, kerosene, turpintine, to possibly run an engine. Thank you for watching by Sul-tech Sul tech

Be Sociable, Share!

{ 23 comments… read them below or add one }

masster64 October 9, 2010 at 4:40 pm

ok, so what is the next step?
I mean, there were many inventors (back to 1910) that created very efficient internal combustion engines (ICE) using vaporized gasoline. but they were seduced only by money or personal glory and ended poor and anonymous (or worse) by not sharing knowledge with humankind.
are you able to show us a working prototype of a super-low consumption ICE ? or is this going to be another suppressed invention ?

jheleno79 October 9, 2010 at 5:35 pm

Great job, I’m planning to build one, but using four transducer, do you think I can use one circuit board for all four or have to use one board for each transducer?
Hope you can help me. Thanks.

audiowan October 9, 2010 at 5:42 pm

Yes, i have used it to vaporize pure alcohol quite well.
It should work with gasoline/alcohol mix also.

audiowan October 9, 2010 at 6:19 pm

Please be careful if modify unit, it can destroy the tuned
shape of the piezo holder and result with less output.
Also if increasing the amplitude of the wave to transducer
watch for heat build-up……maybe u can use several units?

audiowan October 9, 2010 at 6:19 pm

Thanks : >

audiowan October 9, 2010 at 7:13 pm

Maybe they can be found on internet; they are available
here at walmart……or maybe u can build an oscillater and order
the transducer from electronics supply place…experimant for
the best frequency…hope it works out well.

audiowan October 9, 2010 at 7:43 pm

thanks …im glad you liked it.

audiowan October 9, 2010 at 8:20 pm

Hi, you can short the leads of the water sensor out;
or solder the pads on the pc board together (where the leads
plug into the board); then u can remove the sensor wires altogether.

senchele October 9, 2010 at 8:36 pm

Could you put some ethanol in it, I want to see how well it would do with alcohol!!

wojsciech October 9, 2010 at 8:40 pm

YES YOU CAN SPLIT WATER with ultrasonic its frequency between 100khz to 1500khz depends from temp
cheers from poland
wojsciech
please check patent JP 2005247676

erjohnson227 October 9, 2010 at 8:43 pm

An ultrasonic vaporizer simply takes a small stream of liquid and forces it into tiny droplets, that is all the metal element does, it just so happens that a high frequency, such as 50-100khz, is more effective at vaporizing liquids. Other than the surface tension differences between water and gasoline, it should work the same way.

mikeugh October 9, 2010 at 9:24 pm

Hey Buddy, I have a Hyp on what you are doing, I also saw some other ecperiments on youtube where they modified the transducer to achieve a large increase in output vapor. Do you know how to modify one? Or where I could purchase a really good one that puts out a few Gallons per minute? Please e-mail me back thnx and great video

switchgrassfuel October 9, 2010 at 9:49 pm

good video.

Dunndeer October 9, 2010 at 9:59 pm

I have been Looking for transducers because you can also use them for HHO.
Anyway I can’t seem to find them in my Drugstore

mptrax October 9, 2010 at 10:28 pm

that is cool !

diveborg13 October 9, 2010 at 10:56 pm

how do you get the transducer to work on Gas? I’ve tryed as it has a water sensor.

IAMBILLYTHEKID October 9, 2010 at 11:25 pm

Check out my video, Billy the Kid.

hydrogenassist October 10, 2010 at 12:18 am

How little of gas does the transducer need to vaporize in the unit you have created?. Very nice experiment!!

PainlessHHO October 10, 2010 at 12:45 am

This really has me thinking, Pete. The ultrasonic vibrations work very fast on the gasoline, I almost wonder what would be the effect of installing several transducers into the inlet manifold of an injected engine.

Even introducing gasoline mist into the throttle body should increase power and hence mpg.

Do you have any plans for next direction with this?

Thanks for sharing,

Russ.

crob227 October 10, 2010 at 1:28 am

wonder if pulsed dc will work on the trasducer,,, i have one took aprt now and the circuitrykinda looks like just a pulsing circuit.

audiowan October 10, 2010 at 2:11 am

Hi crob227 thanks for watching the video.
Glad it was of benifit to you; the black box is just a few fuses and r.f. filter, i use it on all my experimants. It was just gasoline. Even turpentine, kerosene, alchole, vaperize well…pete

crob227 October 10, 2010 at 2:48 am

was it a water gas mixture or did you put just gas in it?,,, thanks for lighting it. might be tearing one up myself tonight, what was the black box?

good job 5stars

billy dillard April 10, 2011 at 10:45 am

Hi, i’m very interested in your system of vaporizing fuel and i want to build one myself but my electronic knowledge is limited , i need exact plans on what to solder to what and explanations of the parts and there funtions , possibly where to pick up parts . Open to advice on best step to take . Thank You for your time Billy Dillard

Leave a Comment

*

Previous post:

Next post:

BuddyVapesit.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to (“your website name” (amazon.com, or endless.com, MYHABIT.com, SmallParts.com, or AmazonWireless.com). - See more at: http://marketingwithsara.com/amazon/warning-to-all-affiliate-marketers#sthash.6prGdnGl.dpuf